Electro-Fence system


Electro-Fence™ is a powerful intruder deterrent which can be attached to an existing perimeter fence or used as a stand-alone fence. The obvious physical presence of the electric fence with its bright yellow warning signs presents a potent front-line deterrent. Access to the premises can therefore be denied at the perimeter.

As soon as an attempt to climb or cut Electro-Fence is made a safe, short, sharp, very unpleasant shock is felt resulting in a very effective deterrent. Any attempt to breach the fence generates an immediate alarm.

Not only is it legal, it’s also the safest perimeter deterrent out there. Unlike barbed or razor wire fences, which often leave kids and pets sustaining horrific injuries, with Electro-Fence the only thing that will be injured is the trespasser’s pride. In an era where there are plenty out there willing to turn to litigation, that’s worth considering.

Shock Monitoring – predetermined number of shocks will be administered to the intruder
Voltage Monitoring – alarm generated if intruder attempts to reduce the voltage
Cut Monitoring – intruders attempt to cut the wire then an alarm is generated
Short Circuit Monitoring – short circuit to either live or earth wires an alarm is generated
Low Voltage Monitoring – fence wires can still be monitored and alarms generated when High Voltage is switched off

It safe and legal to use
Intruder deterrent AND detector
Can be attached to an existing perimeter fence or used as a stand-alone fence
Physical presence presents a potent front-line deterrent
Extremely effective deterrent

Wires are 95mm apart and are attached to steel galvanized posts spaced approximately 3 metres apart.

A 3.0m high system has 32 wires
A 2.4m high system has 25 wires
A 1.0m high system has 11 wires

Powered by our Pulstar™ series electrical energisers which can operate stand-alone or as part of a fully integrated, networked perimeter Security Solution.

Whatever your site configuration or security challenge we have a Pulstar™ Energiser to meet your needs. Even in areas where you have a high security requirement, but not a reliable mains electricity source, Pulstar™ includes options for battery backup, or can run off a solar panel. Your system will still continue to activate an alarm even in the event of a power outage.

All posts are hot dip galvanized to BS EN ISO 1461. The corner and straining posts are dimensioned at 5 x 25 x 25mm and intermediate posts at 2 x 25 x 25mm. Use of the different post lengths ensures that there is a minimum of 600mm Electro-Fence protruding above any existing fence.

High tensile steel ultra galvanized 2.5mm wire is used for all conductors and comes in coils of approximately 600m runs. The wire is tensioned to 20kg between end posts.

All high voltage cables are insulated galvanized steel wire with a U.V. resistant black polythene insulation.

Gates are normally the weakest point in a system can also be protected with Electro-Fence. The single leaf gate, up to a span of 4 meters, uses a single section. Both gates have a high voltage contact fitted which will activate the alarm on the gate being opened.

Warning signs are prominently displayed on all security fences at spacings not exceeding 10m. They should face to the outside and where access may be gained from the inside, on that side too. The mounting heights above ground level should be at 1.5m.

The intermediate insulators have been designed for minimum contact with the fence wires, keeping capacitive losses to an absolute minimum. They are fitted with a water barrier to prevent tracking. They are attached to the Electro-Fence post with a stainless steel split pin or alternatively with a blind pop rivet.

Electro-Fence is simple to install but impossible to defeat.

The Pulstar™ Energiser generates alarms for a range of events including: Fence voltage drop, tamper, loss of network comms and back-up battery failure. These are reported to the Multisys hub, a control panel, or your alarm system depending on the model and configuration.

Deployable as a stand-alone fence controller, which can be integrated to your alarm control panel, or as a fully networked system controlled and monitored by our Multisys Windows software suite.

Easily configured by software or our hand-held programmer.

Multiple Pulstar™ Energisers can be synchronised over an RS-485 network connection controlled by a central Windows PC.