T-10000B 10kW MF/HF TRANSMITTER - HF TRANSMITTER
Ultra-low latency HF transmitter
The Sunair T-10000B HF Transmitter (MF/HF Transmitter) is the hallmark solution for mission critical communications applications requiring reliable coverage.
The transmitter system combines solid-state radio (SDR) and RF power amplification and control technology to produce a fail-safe high power solution that operates in a frequency range of 1.5 MHz to 30 MHz.
Maximum power output is 10 kW at 100% duty cycle to facilitate longrange hemispheric communications when coupled with the appropriate antenna.
Power is reducible in 1 dB steps down to the 1 kW level.
Standard operating voltage is three phase 338 – 458 Vac, 47 to 63 Hz with a modest power requirement of ≤ 35 kVA.
The Sunair T-10000B HF Transmitter is supplied as an integrated system consisting of the Sunair T-9000S Software-Defined Next Generation HF SSB/ISB Transmitter, F-9800 Post-Selector,
and the LPA-10000A 10 Kilowatt Power Amplifier.
The amplifier architecture consists of eight IPA intermediate power amplifier subsystems that are combined to produce final power output and managed by the Sunair HPAC High
Power Amplifier Controller.
The HPAC actively monitors system balance and performance, and provides power control and safety shutdown in the event of internal module failure such as power supplies, system failures such as air
flow or over temperature or external failures such as high antenna VSWR and short or open circuit.
Advanced built-in-test (BITE) capability reports the status of the T-10000B HF Transmitter (MF/HF Transmitter) down to the Lowest Replaceable Unit (LRU) level providing English messages on the HPAC and the T-9000S front panel displays, and then to a remote site when configured.
Individual LRU fault indication and the system’s intuitive modular design allows for ease of maintenance and upgrade throughout the equipment life cycle at minimal expense. These high-performing niche
products are in daily service as integral components of critical strategic communications solutions for leading defense, peacekeeping, and aviation agencies around the world.
- High Efficiency Solid State Design
- Ultra-low latency up to 94 μs (micro seconds)
- Full Power into Load VSWR up to 2:1
- Comprehensive BITE to LRU
- Full Function Remote Control via Serial or Ethernet
- Tactical Data Link – MIL-STD-188-203-1A TADIL A and Link 11/22 (requires external modems and controllers)
- HF Data – MIL-STD-188-110A/B and STANAG
- ALE – 2G MIL-STD-188-141A/B and 3G STANAG 4538 (with companion transmitter)
- STANAG 4444 Frequency Hopping (requires optional external controller)
CERTIFICATIONS AND STANDARDS
- Tactical Data Link – MIL-STD-188-203-1A TADIL A and Link 11/22 (requires external modems and controllers)
- HF Data – MIL-STD-188-110A/B and STANAG
- ALE – 2G MIL-STD-188-141A/B and 3G STANAG 4538 (with companion transmitter)
- STANAG 4444 Frequency Hopping (requires optional external controller)
10 kW HF transmitter
A 10 kW HF transmitter is a high-power, solid-state system primarily used for long-range communications and broadcasting by military, aviation, and government agencies.
Product Information
- Sunair T-10000B 10kW MF/HF Transmitter (HF Transmitter)
- Architecture: This integrated system uses solid-state radio (SDR) and an amplifier architecture consisting of eight intermediate power amplifier subsystems.
- Reliability: The modular design allows the system to continue operating even if one or two amplifier modules are out of service, increasing overall reliability.
- Control: It features a high power amplifier controller (HPAC) that actively monitors system balance and performance, and provides safety shutdown features.
- Modes: Operates in various modes including SSB/ISB (single sideband/independent sideband), and supports high-speed data transmission.