Telephone

+34 911 87 56 65

Email Address

info@marids.es

Office Address

Av. de España, 3. 1º C, Alcobendas (Madrid), Spain

GET QUOTE

Sunair 5kW HF Transmitter, Wideband

Marcom - Defence and Security Solutions   →  HF ultra low latency   →  HF Ultra-low latency solutions   →  Sunair 5kW HF Transmitter, Wideband
The Sunair T-10000 HP 10kW Military HF Transmitter is the hallmark solution for mission critical communications applications requiring reliable coverage. The transmitter system combines solidstate radio and RF power amplification and control technology to produce a fail-safe high power solution that operates in a frequency range of 1.5 MHz to 30 MHz. Maximum power output is 10 kW at 100% duty cycle to facilitate long- range hemispheric communications when coupled with the appropriate antenna. Power is reducible in less than 1 dB steps down to 500 W level. Standard operating voltage is three phase 338 – 458 Vac, 47 to 63 Hz with a modest power requirement of ≤ 35 kVA. The Sunair T-10000 HP is supplied as an integrated system equipped with the Sunair T-8400 Software-Defined Next Generation HF SSB/ISB Transmitter. As part of this system, the amplifier architecture consists of eight IPA- 8210 intermediate power amplifier subsystems that are combined to produce final power output and managed by the Sunair HPAC High Power Amplifier Controller. The HPAC actively monitors system balance and performance, and provides power control and safety shutdown in the event of internal module failure such as power supplies, system failures such as air flow or over temperature or external failures such as high antenna VSWR and short or open circuit. Advanced built-in-test (BITE) capability reports the status of the T-10000 HP down to the Lowest Replaceable Module (LRM) level providing English messages on the HPAC and the T-8400 front panel displays, and then to a remote site when configured. Individual LRM fault indication and the system’s intuitive modular design allows for ease of maintenance and upgrade throughout the equipment life cycle at minimal expense. These highperforming niche products are in daily service as integral components of critical strategic communications solutions for leading defense, peacekeeping, and aviation agencies around the world. Modes of operation are AME, NB-FM, USB, LSB, ISB, CW, and FSK; Data implemented with internal or external modems. When paired with a companion receiver the T-10000 HP offers 2G and 3G Automatic Link Establishment (ALE) as an internal or external option in accordance with MIL-STD-188-141 A/B/C, FS1045A, and STANAG 4538. Frequency hopping compliant to STANAG 4444 and HF email/data transfer with Automatic Link Maintenance (ALM) compliant to STANAG 5066 are available with optional external controllers. Designed as a high-performance HF system the T-10000 HP complies with the radio requirements of MIL-STD-188-203- 1A and STANAG 5511/5522 (TADIL-A/Link 11 and NILE/Link 22) for tactical data link operation. It also complies with the performance requirements in MIL-STD-188-141C and STANAGs 4203 and 5031. The T-10000 HP is compatible with STANAGs 4285, 4529, 4415, 4481, 4539, and 5065 and MIL-STD-188-110B (including Appendix F ISB) HF modem waveforms. These waveforms can be provided with optional internal or external HF data modems. If equipped with the Internal data modem option the architecture of the T-10000 HP allows for the upgrade of the data modem to MIL-STD-188-110C and other future modem waveforms by a firmware upgrade from the front or rear panel of the T-8400. Full function control, programming and system monitoring/ BITE can be accomplished from the front panel controls and displays, or remotely via Ethernet or USB port. A USB port connector on the front panel is provided for ease of reprogramming the unit’s configuration. Channel, frequency, mode, forward power, reflected power, input audio and other operating information and status are presented in English via a large TFT displays. • High efficiency solid state design Full power into load VSWR up to 2:1 • Comprehensive BITE to LRM (Lowest Removable Module) Full function remote control via serial or Ethernet • Tactical Data Link - MIL-STD-188-203-1A TADIL A and Link 11/22 (requires external modems and controllers) HF Data - MIL-STD-188-110A/B • ALE - 2G MIL-STD-188-141A/B and 3G STANAG 4538 (with companion receiver) • Frequency Hopping (requires optional external controller) - STANAG 4444
The Sunair T-10000 HP 10kW Military HF Transmitter is the hallmark solution for mission critical communications applications requiring reliable coverage. The transmitter system combines solidstate radio and RF power amplification and control technology to produce a fail-safe high power solution that operates in a frequency range of 1.5 MHz to 30 MHz. Maximum power output is 10 kW at 100% duty cycle to facilitate long- range hemispheric communications when coupled with the appropriate antenna. Power is reducible in less than 1 dB steps down to 500 W level. Standard operating voltage is three phase 338 – 458 Vac, 47 to 63 Hz with a modest power requirement of ≤ 35 kVA. The Sunair T-10000 HP is supplied as an integrated system equipped with the Sunair T-8400 Software-Defined Next Generation HF SSB/ISB Transmitter. As part of this system, the amplifier architecture consists of eight IPA- 8210 intermediate power amplifier subsystems that are combined to produce final power output and managed by the Sunair HPAC High Power Amplifier Controller. The HPAC actively monitors system balance and performance, and provides power control and safety shutdown in the event of internal module failure such as power supplies, system failures such as air flow or over temperature or external failures such as high antenna VSWR and short or open circuit. Advanced built-in-test (BITE) capability reports the status of the T-10000 HP down to the Lowest Replaceable Module (LRM) level providing English messages on the HPAC and the T-8400 front panel displays, and then to a remote site when configured. Individual LRM fault indication and the system’s intuitive modular design allows for ease of maintenance and upgrade throughout the equipment life cycle at minimal expense. These highperforming niche products are in daily service as integral components of critical strategic communications solutions for leading defense, peacekeeping, and aviation agencies around the world. Modes of operation are AME, NB-FM, USB, LSB, ISB, CW, and FSK; Data implemented with internal or external modems. When paired with a companion receiver the T-10000 HP offers 2G and 3G Automatic Link Establishment (ALE) as an internal or external option in accordance with MIL-STD-188-141 A/B/C, FS1045A, and STANAG 4538. Frequency hopping compliant to STANAG 4444 and HF email/data transfer with Automatic Link Maintenance (ALM) compliant to STANAG 5066 are available with optional external controllers. Designed as a high-performance HF system the T-10000 HP complies with the radio requirements of MIL-STD-188-203- 1A and STANAG 5511/5522 (TADIL-A/Link 11 and NILE/Link 22) for tactical data link operation. It also complies with the performance requirements in MIL-STD-188-141C and STANAGs 4203 and 5031. The T-10000 HP is compatible with STANAGs 4285, 4529, 4415, 4481, 4539, and 5065 and MIL-STD-188-110B (including Appendix F ISB) HF modem waveforms. These waveforms can be provided with optional internal or external HF data modems. If equipped with the Internal data modem option the architecture of the T-10000 HP allows for the upgrade of the data modem to MIL-STD-188-110C and other future modem waveforms by a firmware upgrade from the front or rear panel of the T-8400. Full function control, programming and system monitoring/ BITE can be accomplished from the front panel controls and displays, or remotely via Ethernet or USB port. A USB port connector on the front panel is provided for ease of reprogramming the unit’s configuration. Channel, frequency, mode, forward power, reflected power, input audio and other operating information and status are presented in English via a large TFT displays. • High efficiency solid state design Full power into load VSWR up to 2:1 • Comprehensive BITE to LRM (Lowest Removable Module) Full function remote control via serial or Ethernet • Tactical Data Link - MIL-STD-188-203-1A TADIL A and Link 11/22 (requires external modems and controllers) HF Data - MIL-STD-188-110A/B • ALE - 2G MIL-STD-188-141A/B and 3G STANAG 4538 (with companion receiver) • Frequency Hopping (requires optional external controller) - STANAG 4444

HF wideband – Communications systems
NATO BRASS Enhancement 2 Technical Architecture (BRE2TA)
BRE2TA-compliant equipment supports bandwidths up to 48 kHz
NATO BRASS Enhancement 1 Technical Architecture (BRE1TA)
BRE1TA (BRASS Enhancement 1 Technical Architecture)

New generation Military HF transmitter, Military HF transceiver, Military HF receiver, Military HF Power Amplifier & Military Pre/Postselector

Sunair Electronics, USA has a history of leadership in the arena of secure radio communications for military, government, civil aviation, and commercial applications worldwide.

Sunair New Generation Military HF products: Sunair RT-8500WB HF Transceiver Wideband, Sunair T-10000 HP 10kW HF Transmitter Wideband, Sunair R-8400 HF Receiver Wideband, Sunair 8220WB 1 kW HF Transmitter Wideband, Sunair LPA-8220 (1kW) HF Power Amplifier Wideband, Sunair 8220WB 1 kW Transceiver Wideband, Sunair RCU-8310 Remote Control Unit, Sunair F-9810B Pre/Postselector.

Sunair New Generation HF products are the next generation of products supporting mission-critical operations, and are designed for all strategic environments, including C3 (command, control, and communications), fixed station, shelterized, transportable, vehicular, and shipboard. When coupled with our complementary accessories, our equipment covers all contemporary requirements – from basic voice communications to data, email, fax, chat, high speed ALE, encryption, security, and interoperability.